Free plans for SZD-55 - Nexus 900



  • Rewiev:

    SZD-55 rc GLIDER, also named Nexus 900 sailplane in rc world: original design by Franck Aguerre!

    Free plans for 3D printed rc glider SZD-55


    • ROTOWING system with very easy commands setup (2 micro servo and you fly!)
    • TOTAL WEIGHT: 150gr~
    • WINGSPAN: 93cm
    • AIRFOIL: fad05cnc (credits to Franck Aguerre)
    • FLY DIFFICULT: medium (not for beginners), but fun guaranteed!
    • TOTAL PRINTING TIME: 15/20 hours
    • Ready to fly in 2-3 hours of works/settings.

    Now print and fly!

    Free plans for 3D printed rc glider SZD-55

    Material needed

    • 1 x wing joiner: best choice: 3mm carbon rod — 50cm length; alternative: any rod of 3mm, carbon or steel, from 20cm to 50cm;
    • 4 x wing/servo commands rod: 0.8/1mm steel: 5cm; (umbrella rod?)
    • 1 x shaft for fix commands to fuselage: 2mm steel: 5cm; (bicycle spokes is 2mm)
    • 2 x 3.7gr servo (any light micro servo);
    • 1 x 1s lipo 380mAh (any battery 10/20gr);
    • your RX (2 channels);

    Superglue (cyanoacrylate) and optional double-sided tape. (also epoxy is ok, but more complex in my opinion)

    Electronics:

    3.7g Micro Analog Servo
    Buy: BangGood, AliExpress
    Power HD-1370A 0.6KG 3.7g
    Buy: BangGood, AliExpress
    3.7G Micro Light Servo
    Buy: BangGood, AliExpress
    RC Quadcopter Spare Parts
    Buy: BangGood, AliExpress
    Gens Tattu 3.7v 380mAh
    Buy: BangGood, AliExpress

    Free plans for 3D printed rc glider SZD-55

    3D printing settings:

    Fuselage: (3 parts — 60gr~ total weight — vertical print)

    • tail: 12gr — solid infill every 25 layer (5mm), 0% internal infill, 1 perimeter, 3 top, 3 bottom.
    • center: 10 gr — solid infill 4% (one X cross), 1 perimeter, 3 top, 3 bottom.
    • head: 40gr — solid infill ~10%, 1 perimeter, 3 top, 3 bottom. Supports on servo housing and wings commands rod (not on wing joiner hole and battery top hole, if possible).


    Wings: (3 parts — 60gr~ total weight — vertical print)

    • 30gr/35gr each wing, 3% infill and solid infill every 25 layer (5mm). You need to mirror flip the wing parts for left/right wing.


    Canoppy: (<10gr — vertical print )

    • 0-3% internal infill, 1 perimeter, 3 top and 3 bottom (sand for correct positioning), maybe support.


    Commands:

    • strong print: 3+ perimeter, 50%+ infill. 3+ top/bottom. Mirror flip for left/right command.



Tags: glider
Rating: 4 Votes: 3 Your vote:
Comments (0)

No comments yet. Yours will be the first!

How to make video

Best FPV Camera For $15 Foxeer Razer Micro

RC Plane Poster  0  1500
In-Depth Review of the Foxeer Razor Micro 5gram FPV Camera that We put to the Test and impressed how good the video footage of looking straight into the sun and it´s super small and...

 


DIY RC Seaplane at home

RC Plane Poster  0  1431
How to make rc airplane 

 

 


Home made rc plane

RC Plane Poster  0  1849
This is my YouTube channel in which I am going to share information about RC Airplane Electronics Basic

 


How to Make Rc Simulator At Home . DIY Build

RC Plane Poster  0  1195
In this vedio you will be learn how to simulator at home

 


Homemade propeller for RC airplane (HOW IT IS MADE)

RC Plane Poster  0  2088
In this video i made a wooden propeller for my homemade rc airplane

 


Powerful Mini 5 Cylinder Radial Engine

RC Plane Poster  0  1534
How to Make an Aircraft Engine at Home